Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use Instrukcja Użytkownika Strona 113
- Strona / 148
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
112 CHAPTER 9 SETUP OUTPUT COMMUNICATIONS
well for most devices. e minimum value is 0.01 seconds and the maximum value is 1.00
seconds.
e Undo button returns all Output Communication parameters to the values they had
when the task was started; the OK button sends all the Output Communication parameters
to the sensor (the settings are not saved to FLASH at this point). Clicking the Cancel button
will cause you to lose any changes and return to the CAZ menu.
Secondary Push Manager
e secondary push manager is dedicated to transmission of trigger speed data. e set-
tings of this secondary push manager are at the bottom of the Setup Output Communica-
tions screen. By default, this push manager is disabled (Port option set to None).
is section describes the settings contained in the bottom section of the Output Commu-
nication Setup screen.
Select trigger speed options
If the trigger speed port is set to 1 (control bus) or 2 (data bus) trigger speeds will be pushed
on the corresponding port. e trigger speed communicates the speed of a vehicle that
activated the channel. When a pulse channel is used to signal trigger speeds, a speed will be
pushed for each uniquely detect vehicle.
e trigger speed option only monitors alert 1, zone 1 of the selected channel. e trigger
speed channel is selected using the channel drop down control on the right.
e trigger speed tag is a 6-character tag that is inserted aer the speed bytes of the trigger
speed message. e trigger speed tag is intended to be used by the customer to identify
where the speed came from. It can also be used to customize the terminator sequence if
necessary.
Note
In some applications it is recommended to select the trigger speed channel to cor-
respond to a pulse channel type. A trigger speed will be sent when each uniquely
tracked vehicle enters the zone of the pulse channel. One such application is to calcu-
late 85th percentile speed to an intersection approach. The trigger speed data can be
forwarded by a terminal server to a UDP listener which would timestamp the speed
data, store it in a database, and filter speeds based upon signal light status.
- SmartSensor Advance 1
- SmartSensor 2
- Contents 4
- Introduction 6
- SmartSensor Advance Package 7
- Selecting a Detection Method 7
- Selecting a Mounting Location 8
- Installing the SmartSensor 14
- Selecting the Mounting Height 16
- Mounting the Sensor 17
- Distance 18
- Oset (perpendicular) 18
- Aligning the Sensor 20
- Figure 1.9 – Viewpoint 1 21
- Using the Viewfinder 22
- To target 23
- Figure 1.12 – Viewpoint 1 23
- Grounding the Sensor 26
- Connecting Power and 28
- Surge Protection 2 28
- Mounting the Backplate 29
- Connecting AC Power 29
- Push this button to 32
- (see Figure 2.8) 35
- Contact Closure Connections 37
- Using SmartSensor Manager 38
- Advance 3 40
- Figure 3.3 – Shortcut Options 42
- Communication 4 44
- Serial Connection 45
- Internet Connection 46
- Virtual Connection 47
- Virtual Sensor File 48
- Selecting a Tracker Log File 49
- Multi-drop Network 50
- Address Book 51
- Check Hardware 53
- Communication Error Log 54
- Sensor Settings 5 58
- Figure 5.2 – General Tab 59
- Communication Tab 60
- Sensor Configuration 6 62
- 1. Installation Details 63
- Positioning the Sensor 64
- 3. Manual Radar Adjustment 66
- Editing Sensitivity 67
- Changing the PGA 70
- Channels-Alerts-Zones 7 72
- Channels 73
- Channel 1 74
- Priority Channel 75
- Pulse Channel 78
- Normal Channel 80
- Latched Channel 82
- Enabling an Alert 85
- Logic (OR/AND) 85
- Inverted Zones 85
- Range (ft) 86
- Speed (mph) and ETA (s) 87
- Right Sidebar 93
- (All) Channels 94
- Individual Channel 95
- Channel LED 97
- Zone LED 98
- Alert LED 98
- Roadway Display 99
- Qualified Count 102
- Dynamic Density 103
- Tri-view 104
- Tracker Highlighting 105
- Left Sidebar 107
- Figure 8.24 – Log File 109
- Figure 8.25 – Pulse Log File 109
- In this chapter 110
- Primary Push Manager 111
- Specify output frequency 112
- Secondary Push Manager 113
- Templates 10 116
- Creating a Channel Template 117
- Importing a Channel Template 117
- 118 CHAPTER 10 TEMPLATES 119
- Tools 11 120
- Backup/Restore Tool 121
- Restoring the Configuration 122
- Restoring to Factory Defaults 123
- Beam Alignment Tool 124
- Serial Terminal 125
- Rack Card Tools 126
- Using the Rack Card Tool 127
- Firmware Version 128
- Signal Cards Switch 128
- Channel Outputs Switch 128
- Fail Safe Mode 133
- Rack Card Dip Switch 133
- Click 104 Configuration 135
- Appendix 138
- Creating Custom Cables 139
- Appendix B – Cable Lengths 140
- APPENDIX 143 144
- APPENDIX 145 146
- 146 APPENDIX 147
Powiązane produkty i podręczniki dla Czujniki Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use
(78 strony)
(4 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji