Wavetronix Command Collector (CMD-DCx) - User Guide Instrukcja Użytkownika Strona 92
- Strona / 117
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
CHAPTER 7 SYSTEM PAGE 91
Consecutive Failures Error Threshold – Shows the number of consecutive failed con-
nection attempts that need to occur for the status to change to “Error.”
Recent Data Interval Expiration – Shows the number of collection interval time peri-
ods that can pass before the recent data is expired. is means that if a sensor has a col-
lection interval of 30 seconds (and an interval expiration setting of 3) and the Collector
is not able to retrieve data from that sensor for over 90 seconds then the recent data
will expire. When a sensor does not have valid recent data, Collector will not display
data for that sensor on either the Sensors page, the Sensor Cong page, the TMDD
export, or recent data table. Whether a sensor has recent data or not has no eect on
sensor status.
Timer Settings
e Timer Settings section allows you to control when Collector downloads the current
conguration from each sensor, and to sync the onboard sensor clock with the current
server time (see Figure 7.10).
Figure 7.10 – Timer Settings
e Timer Settings section contains two automatic timers, which run on a xed schedule,
as well as a time synchronization control. Below is a list and description of the timer setting
options:
Update Config Timer – Runs an Update Conguration job for every sensor registered
in Collector and retrieves and saves the current conguration to the Collector data-
base. Selecting the Update Cong Timer checkbox will toggle the automatic opera-
tions. e intervals will normally default to every 360 minutes (6 hours) and have a
minimum of 10 minutes. e Next Run eld will show the next scheduled run based
on the current interval. An error alert will be displayed if the entered interval is invalid.
Synchronize Clock Timer – Runs a Sync Time job for every sensor registered in Col-
lector and changes the onboard system time for each sensor to the time on the Collec-
tor server. Selecting the Synchronize Clock Timer checkbox will toggle the automatic
operations. e intervals will normally default to every 360 minutes (6 hours) and have
a minimum of 10 minutes. e Next Run eld will show the next scheduled run based
on the current interval. An error alert will be displayed if the entered interval is invalid.
- Command Collector 1
- Contents 4
- Chapter 8 Help Page 103 5
- Introduction 6
- Data Storage 7
- Installing Command HQ 1 8
- Wavetronix representative 10
- Install button 12
- Command Licensing 13
- Oine Activation 14
- In this chapter 18
- Logging In 18
- Service Not Started Errors 19
- Common Web Interface Features 20
- Navigation/Status Control 21
- Web Interface Context Help 22
- Sensors Page 3 24
- Sensor List 25
- Network(s) 27
- Location 28
- Description 28
- Interval (Intrvl) 28
- Frequency (Fq) 28
- Figure 3.5 – Paging Control 29
- Display Settings Control 30
- Filter Controls 31
- With Com Status 32
- With Data Status 32
- Figure 3.10 – By Data Filter 33
- Sensor Toolbar 4 34
- Add Sensors 35
- Modem Support Using COM Ports 37
- Adding Ranges of Sensors 37
- Adding from an Address Book 38
- Remove Sensors 39
- View Errors 39
- Sensor Error Display Settings 40
- Sensor Error Queries 41
- Exporting Sensor Errors 41
- Collection 43
- Intervals 43
- Commands 45
- Networks 46
- Figure 4.18 – Search Box 48
- Figure 4.19 – Search Results 48
- Sensor Configuration Page 5 50
- Sensor Info Bar 51
- Com Status 52
- Data Status 52
- Communication Status Graph 52
- Data Status Graph 53
- Sensor Information 54
- View Log Button 54
- Sensor Config Tab 55
- Custom Configuration Panel 56
- Figure 5.7 – Basic Tab 57
- Figure 5.8 – Advanced Tab 58
- Lanes/Approaches Tab 59
- Setting Custom Lane IDs 60
- Approaches 60
- Sensor Commands Tab 61
- Data Query Tab 63
- Data Query Graphs 64
- Data Query Tables 65
- Data Page 6 68
- Selecting Sensors 69
- Define and Request Report 69
- Output Report Type 70
- 70 CHAPTER 6 DATA PAGE 71
- CHAPTER 6 DATA PAGE 71 72
- Figure 6.6 – Monthly Report 72
- 72 CHAPTER 6 DATA PAGE 73
- CHAPTER 6 DATA PAGE 73 74
- Saving a Report Template 75
- Export Tab 76
- Automated Custom Export 77
- Current Automated Export 78
- 78 CHAPTER 6 DATA PAGE 79
- CHAPTER 6 DATA PAGE 79 80
- System Page 7 82
- Status Tab 83
- Networks Tab 83
- Error Log Tab 84
- Figure 7.4 – Error Log Tab 85
- 84 CHAPTER 7 SYSTEM PAGE 85
- Users Tab 86
- Network Permissions 87
- User Privileges 87
- Settings Tab 88
- Information 89
- Mail Settings 89
- Status Settings 90
- 90 CHAPTER 7 SYSTEM PAGE 91
- Figure 7.9 – Status Settings 91
- Timer Settings 92
- Data Settings 93
- Collection Settings 94
- Database Settings 95
- Log Level 95
- Session Timeout 95
- Classes Tab 96
- Notifications Tab 97
- Journal Tab 98
- Service Tab 99
- Support Tab 101
- Figure 7.20 – Support Tab 102
- Help Page 8 104
- User Guide Tab 105
- License Info Tab 105
- License Agreement Tab 106
- Figure 8.6 – Support Tab 107
- 106 CHAPTER 8 HELP PAGE 107
- Driver Reference 9 108
- Custom Fields 110
- 3M 940 Trac Monitoring Card 111
- EIS RTMS X2/X3 112
- Autoscope 113
- Mikros Data Logger 114
- Class Mappings 115
Powiązane produkty i podręczniki dla Oprogramowanie Wavetronix Command Collector (CMD-DCx) - User Guide
(4 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji